Dankoff Flowlight Booster Pump Cat. No. 2910-12 Weight 20 lbs

The Dankoff Flowlight Booster Pump provides city water pressure anywhere. It has been a standard in home renewable energy systems since 1986. It is economical for domestic water supply, drip irrigation, and water purification. A booster pump is far more cost effective than an elevated tank, providing pressure equivalent to over 100 feet (30 m) of elevation. It uses one third to one half the energy of a conventional AC pump, and eliminates high starting surges. It is more powerful, quieter, and much more durable than plastic RV/Marine pumps. Wearing parts are replaceable, and typically last 5 to 10 years. Overall life expectancy is 15 to 20 years. Our complete instruction manual and easy installation kit make this pump simple for anyone to install and service, with no previous experience. Suction Capacity Low speed model 20 vertical feet (6 m) at sea level Standard model 10 Feet (3 m) at sea level Subtract 1 ft. for every 1,000 ft. altitude (1 m for every 1,000 m) for both versions. Note: Suction capacity may be further limited by intake pipe friction. Excessive suction causes cavitation (vapor bubbles) creating noise and excessive wear. Intake piping should be 1” or larger. Pump should be mounted as close to the water source as possible. Choice of Capacity Standard Model for highest flow Low speed model (DC only) has higher pressure capacity, and is best when: Suction lift greater than 10 feet Intake pipe smaller than 1” size Extra-quiet operation is desirable Choice of Voltage 12, 24 or 48 V DC, others (inquire) 115 V AC (low surge PM motor minimizes inverter and wire size) Construction Rotary vane pump mechanism (pulsation-free) Solid forged brass pump body with carbongraphite and stainless steel working parts NSF® approved for drinking water Handles sea water and dissolved minerals Survives most freezes Permanent magnet, ball bearing DC motor, thermally protected Clear flexible hoses and pressure relief valve included Additional Needs Battery-based power system (12 or 24 V) or AC (minimum 300 W inverter) Pressure tank, captive air type, minimum size: 40 gallon (150 l); larger is better, to reduce cycling and increase reserve capacity; available locally Foot valve (if pump is placed higher than water source) Installation Pump may be mounted horizontally or vertically. Pump must not be submerged. It may be placed inside a 6” (120 cm) or larger well casing, suspended by rope. Dimensions Length 16.5” (42 cm) Weight 15 lbs (7 kg) Flexible hose ends have 3/4” or 1” male pipe thread Warranty 1 year against defects in materials and workmanship Battery Systems 2.7gpm @ 65 psi 178.2 Watts Includes the Flex Tube Install Kit 2910-12 Low Speed Model for 12V Max Amps: 20 2910-24 Low Speed Model for 24V Max Amps: 10 2910-48 Low Speed Model for 48V Max Amps: 5   4.1gpm @ 65 psi 270.6 Watts Includes the Flex Tube Install Kit 2920-12 Standard Speed Model for 12V Max Amps: 25 2920-24 Standard Speed Model for 24V Max Amps: 15 2920-48 Standard Speed Model for 48V Max Amps: 5.5   5.0gpm @ 65 psi 264 Includes the Flex Tube Install Kit 2930-24 Standard Speed Model (1/2 HP) for 24V Max Amps: 16 2930-48 Standard Speed Model (1/2 HP) for 48V Max Amps: 8 Model: 2910, 2.7gmp : $909.00 2920, 4.1gpm : $1,009.00 2930, 5gpm : $1,699.00 Voltage: 12 volt 24 Volt 48 Volt